Vdo WL X1 DW User Manual download pdf (Page 15)

X1DW VDO CYCLECOMPUTING28

F I

I F

www.vdocyclecomputing.com X1DW 29

DGBD GB

3.2 Cadence option

The cadence menu is only available if

the cadence transmitter is installed,

the transmitter was recognized during pairing.

After pairing the cadence transmitter, the current ca-

dence is shown in section 2 of the display.

In function mode it is possible to select the CADENCE/

MORE menu using the using the up/down

buttons.

Conﬁrming with

opens the menu and gives you

access to the information.

Using you come to:

AVG CADENCE

MAX CADENCE

Resetting the trip data also sets the cadence data

back to zero.

4 Installation

4.1 Fitting the transmitter, magnet and handlebar holder >>> P01

Start by ﬁtting the transmitter and magnet.

ATTENTION: The transmitting distance between

the transmitter and the computer on the handle-

bars should not be more than 60 cm (transmission

range).

step 1 Place the rubber pad under the transmitter.

Fit the transmitter on the same side of the fork

where you later want to ﬁt the computer to the

handlebars (right or left) using the cable ties sup-

plied (loose at ﬁrst, do not pull tight just yet).

ATTENTION: The sensor mark on the transmitter

must point to the spokes.

Depending on the room available, the transmitter

can be ﬁtted at the front on the forks, inner side

of the fork or backside of the forks. >>> P04

step 2 Place spoke magnet around an outer

spoke. The silver middle of the magnet points

towards the transmitter. Align the magnet to the

sensor mark on the transmitter with a gap

of about 1 – 5 mm.

Step 3 Align transmitter and magnet for good and

fasten in place: Pull cable ties tight and push

magnet in ﬁrmly.

Step 4 Decide whether ﬁtting to handlebar or

stem and turn the base of the handlebar holder

by 90° accordingly. To do so, undo the screws in

the holder, take out the foot and turn it 90°, insert

and tighten the screws again.

ATTENTION: Do not over tighten screws.

To wake it up out of despatch mode, press the

button simultaneously for a few seconds.

The computer is now ready for use and tells you

so by showing the language setting.

See also Chapter 5.1

4.2 Switching on the computer for the ﬁrst time >>> P02, Display see Chapter 5.1

Waking up from despatch mode

The computer is delivered with a battery installed.

To reduce the battery consumption, the computer

is put into despatch mode. The display is empty

(no display).

4.3 Installing the battery in the computer >>> P05

Your VDO computer is supplied with a 3V battery

(type 2032).

The battery is already installed when supplied.

To change the battery, proceed as follows:

step 1 Place the battery in the computer casing

with the +terminal facing up.

Step 2 Make sure that the battery does not

get wedged.

step 3 Take care that the rubber seal lies ﬂat on

the battery compartment lid.

Step 4 Insert the battery compartment lid into the

opening and turn it with a coin to the right as far

as it will go (approx. 1/3 turn).

TIP for changing battery: VDO recommends chang-

ing the battery once a year. Buy a new battery in

good time to ensure the wireless transmission

works perfectly. When the battery is changed,

all settings and the total kilometres cycled

are saved.

step 5 Guide the cable ties through the slot in the

handlebar holder, place around the handlebars

or the stem and pull (do not pull tight just yet).

Step 6 If ﬁtting to handlebar: Align computer

angle to achieve optimum readability. Now pull

cable ties tight. Snip off protruding ends with

clippers.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 263 264

Comments to this Manuals

No comments

Vdo WL X1 DW User Manual Page 15

Comments to this Manuals

Related products and manuals for For bicycles Vdo WL X1 DW